Matched Content

Friday, May 31, 2013

Simple Battery Voltage Indicator With LED


This indicator circuit will monitor battery voltage. It's simple circuit will avoid confusing when assembling and not prone to malfunction during operation. The circuit consumes about 0.43 mA current at a voltage of 12 volts, power is about 0.00516 watts. Because that power consumed is very small then this indicator can be used to continuously monitor the voltage, for example as an indicator vehicle dashboard. LED lights as accessories that can adorn the dashboard.

See video when testing with variable voltage power supply here.

Watch test video on vehicle for battery voltage and electric system interpretation, please read "Battery And Charging System Condition Interpretation By Voltage".

The circuit is using zener diode as voltage reference and it is known to have good stability and high accuracy. The circuit is quite reliable yet inexpensive when compared to the expensive digital voltmeter but sometimes error, as well as analog voltmeter which is less accurate when placed in a certain position.

Maximal voltage for charging dry cell battery) is around 13.8 volts. Maximal voltage for charging wet cell battery is around 14.4 volts. More details on "Charging Your Vehicle Battery".

In addition to monitoring the vehicle battery voltage, the circuit can also be used for battery charging indicator with wind turbine (wind charger) as the article "Pico Wind Turbine With Bicycle Wheel".




Resistor 1 (R1) is 10 kiloohms 0.5 watts, it filters high voltage caused by magnetic field induction alternator, dynamo, and transformer that is used to recharge battery.

Diode 1 (D1) is 1N4007 securing the circuit if there is an error connection to the battery. D1 will cause voltage that is fed to the circuit will be dropped 0.6 volts.

R1 and D1 may be omitted if the circuit operation is considered fairly safe. If D1 abolished then all values of zener diode must be added by 0.6 volts.

Zener diode 1 (Dz1) has value 11 volts 0.5 watts, will determine the voltage that makes the transistor (T) turned on and LED light up. Note that zener diode is installed with reverse position of ordinary diode.

Base resistor (Rb) with value 680 kiloohms 0.25 watts determines the current through transistor and the LED to adjust the brightness of the LED when lit.

LED has a 5 mm diameter with transparent casing and yellow light.

Transistor (T) is BD139 serves as a switch and will connect if it's base energized. Base of the transistor will get current if the voltage beyond a certain voltage. That certain voltage is zener diode 1 (Dz1) plus diode 1 (D1) voltage (0.6 volts) plus the base emitter voltage of the transistor (0.6 volts). If Dz1 valued at 11 volts, the voltage that makes the transistor connects and allows the LED to light up is:

11 + 0.6 + 0.6 = 12.2 volts

The schematic may have some circuits to monitor the battery voltage. As the above schematic, there are three circuits as an indicator for three voltage levels. Circuit in the center is using a zener diode (Dz2) with value of 12 volts 0.5 watts. The LED in the center circuit will be lit if the battery voltage is reached:

12 + 0.6 + 0.6 = 13.2 volts

Rightmost circuit is using a zener diode (DZ3) with value of 12 volts and it has diode 1N4007 added to increase zener voltage as high as 0.6 volts. LED will light up if the battery voltage is reached:

12 + 0.6 + 0.6 + 0.6 = 13.8 volts

If using a crystal diode OA90, then the zener voltage can be increased by 0.2 volts.

This circuit can be modified so that the LED is turned on at a certain voltage, by replacing zener diode, or add 1N4007 or OA90 diode on the transistor base as shown by the rightmost circuit.

Number of LED lights also can be added as needed. To monitor battery voltage, circuit should consist of 4 pieces LED lights representing 12, 13, 14, and 15 volts. LED light representing 14 volts should be orange colored, to warn that the battery voltage is maximal for wet cell battery, and too high for dry cell battery. LED light representing 15 volts should be red colored, to warn that the battery voltage exceeds the maximum voltage allowed for wet cell battery.

For voltage indicator circuit of  12, 13, 14 and 15 volts, it is using zener diodes 11, 12, 13, and 14 volts. Zener diodes voltage are a little smaller, because of the loss of voltage on the input diode (D1) and the base emitter transistor respectively of 0.6 volts, so the total loss of voltage is 1.2 volts.

For 24-volt battery, circuit is using zener 22, 24, 26, and 28 volts. If you can not find the appropriate zener voltage, it can use a 1N4007 diode (0.6 volts) or OA90 crystal diode (0.2 volts) to adjust or increase the zener voltage.

Here are the results of my tests done to determine the current consumption at each voltage level with 680 kilohm resistors for all LEDs:
12 volts 0.43 mA
13 volts 0.80 mA
14 volts 1.03 mA
15 volts 1.57 mA

Below photo shows voltage indicators unit  which has different LED lights, which are: white for 12 and 13 volts, orange for 14 volts, and red is indicating 15 volts. Those white LEDs are very bright while red LED is the faintest.


So I modify base resistors, for very bright white LEDs that represent voltage of 12 volts is using 2.2 megohm resistor, while white LED that represent the voltage of 13 volts is using a 1.6 megohm resistor. Orange LED as indicator for 14 volts is using 82 kilohm resistor. Red LED that indicates the voltage of 15 volts is using 33 kiloohm resistor. Total current consumed for each voltage level is:

12 volts 0.3 mA
13 volts 0.6 mA
14 volts 0.8 mA
15 volts 2.2 mA

It won't be a problem for high current consumption at 15 volts, as it means that charging system is over voltage. Therefore it needs load to consume that excess voltage.

As a guidance to set the LED brightness, forward voltage at LED pins (anode and cathode) should be about 2 volts to produce bright LED light, and LED will last longer. If the forward voltage exceeds 3 volts, the LED can be broken.

Read also laptop charger can be used to recharge car battery.

Photo above looks out of focus because the camera lens is dazzled by the light of white LEDs. That's why white LEDs are using very big resistors. If the circuit is using only white LEDs, current consumption will be very very small.

Download datasheet dioda zener,  dioda 1N4007,  transistor BD139

17 comments:

  1. Looking for high quality and best perfomence Street Light? Then we are the best for you, who suit your expectations. We have huge experience on this field. We are 100% dedicated to find you LIBRA Series LED Street Lights.
    You can buy LIBRA Series LED Street Lights here and here are numberius clients buy our products. We are provide only high quality LIBRA Series LED Street Lights for you with always customers support.


    If you want to know more, Please check out here - https://kanglight.com/libra-series-led-street-lights/

    ReplyDelete
  2. I'm amped up for such obsessions so I will address page where it is cool portrayed. LED robots

    ReplyDelete
  3. This particular is usually apparently essential and moreover outstanding truth along with for sure fair-minded and moreover admittedly useful My business is looking to find in advance designed for this specific useful stuffs… 2cl2fm

    ReplyDelete
  4. I really like your blog. Great article. It's most evident, people should learn before they are able to Multifunctional Car Seat Organizer

    ReplyDelete
  5. White LEDs, then again are as yet growing in fact and ought not be shopped in light of cost alone. outdoor hanging ball lights

    ReplyDelete
  6. Be that as it may, there are likewise a few issues to know about while involving LED lighting in your aquarium.
    outdoor ball lights

    ReplyDelete
  7. Les bandes lumineuses à LED en gros, les néons LED Flex et les enseignes au néon personnalisées peuvent également fournir des solutions professionnelles d'éclairage LED intelligent. néons à LED

    ReplyDelete
  8. Nothing compares to Weber using Genesis sort of grills. That is certainly the type gas grills which have been that will always make sure that they deliver a high performance part of down interval headlight assembly

    ReplyDelete
  9. Your home furniture usually tells about you, your personality and your taste.led cubes

    ReplyDelete
  10. Extremely pleasant article, I appreciated perusing your post, exceptionally decent share, I need to twit this to my adherents. Much appreciated!.  Marsauto LED bulbs

    ReplyDelete
  11. he most suitable change cards and procedures to use in applications that involve exchanging voltage signs will rely upon the extent and impedance of the voltages in question.
    عالية الجهد مكثف السيراميك

    ReplyDelete
  12. Pretty good post. I just stumbled upon your blog and wanted to say that I have really enjoyed reading your blog posts. https://www.ronselighting.com/product/all-track-light

    ReplyDelete
  13. Neon or Driven signs are a unimaginable method for drawing in individuals into your business. A neon open sign or drove open sign blazing at your retail facade is a reasonable, powerful method for driving the traffic to your business.LED Neon Signs

    ReplyDelete
  14. Proficient coordinators comprehend that utilizing quality gear that will give the best picture and sound betterly affect the crowd and endeavor to involve the most recent innovation in their benefit to acquire that outcome. LED Video Wall

    ReplyDelete
  15. At the point when the vehicle is presented to coordinate daylight in summers for longer timeframes, it speeds up the course of erosion and dissipates the electrolyte. This lessens the existence of a battery making it more fragile. In this way, try not to get your vehicle warmed by daylight by leaving in a reasonable shade.Best solar companies in arizona

    ReplyDelete
  16. Customary voltage testing will surrender you a heads on whether your ongoing power supply is sufficient to control any extra gear or machine that you should gethigh voltage polypropylene film capacitors

    ReplyDelete

Your positive comment will be highly appreciated to improve this site