Matched Content

Wednesday, December 21, 2016

Pistol Penunjuk Laser Dengan Sasaran Optikal





Penunjuk laser atau laser pointer pada foto di atas mempunyai gagang kayu sehingga bentuknya menjadi pistol laser. Laser diaktifkan dengan menarik picu. Terdapat sirkuit yang menggunakan kondensor agar menyalakan laser selama kurang dari 1/4 detik. Tampak seperti ada peluru yang dilontarkan, sebagaimana video berikut:


Dengan menggunakan saklar, laser dapat disetel agar bersinar terus-menerus jika perlu digunakan sebagai pointer, saat presentasi di kantor misalnya.

Sasarannya seperti terlihat di bawah ini, akan membelokkan sinar laser sehingga memproyeksikan bentuk garis pada dinding atau layar di belakang sasaran tersebut. Sehingga dapat diketahui jika sasaran terkena sinar laser. Jika tidak mengenai sasaran maka sinar laser akan terlihat membentuk sebuah titik pada dinding.

 

Pada video berikut sasaran akan memproyeksikan sinar laser berbentuk bintang jika tepat di tengah sasaran (bullseye)


Jika terkena bagian pinggir sasaran maka laser akan terproyeksi membentuk garis. Video berikut memperlihatkan cahaya laser pointer saat mengenai setiap bagian lensa sasaran.



Karena sinar lasernya masih bisa dinyalakan secara kontinyu, maka pistol laser ini tetap bisa dipakai sebagai pointer untuk presentasi.

Tuesday, November 22, 2016

Radiator & Air Conditioner Fan Motor Noisy



Radiator fan and air conditioner condenser fan motor noisy motor can be repaired by lubricating shaft of the motor. Lubrication can be done from the outside without opening the motor housing. But the fan needs to be removed to get access to the shaft.

The cost of this repair is quite cheap if compared with the price of a new motor that can reach hundreds dollar.

Once repaired then the motor shaft will rotate more smoothly. If the motor is connected to the battery and measured with a digital ampere meter then it is obvious that the consumed current becomes lower. Because the motor will generate electricity if the shaft is rotated by hand, when measured by a digital volt meter then the produced voltage is higher after repair.

Read also the fan motor generating electricity powered by wind turbine.

The procedure is quite easy and can be done at your garage. On some vehicles, it needs to open radiator hose to pull out the frame of the fan motor. Sometime it needs to remove the front grille, to get access to remove the air conditioner fan.

If the radiator hose must be removed, a new radiator coolant will be needed. Do not reuse the used radiator coolant, although it looks clean. Because of it's chemical properties may have changed because contaminated by dirt. Contaminated coolant is acidic (corrosive), radiator will be corroded. If the radiator coolant is not available, it can be replaced with clean water. And later coolant can be added into the radiator.

After the fan frame removed from the vehicle, it can be seen a nut that holds the fan on the motor shaft, as the following photos.


Loosen and remove the nut. Remove the fan of motor shaft.

In some types of motor, there is a spacer ring on the motor shaft. That spacer ring can be seen after the fan removed, as pointed by the red arrow in the photo below.


The ring can be easily removed by hand.

Spray lubricant such as WD-40 on the base of the motor shaft. Rotate the shaft by hand. The shaft may also be rotated by supplying electric current to the motor. Be cautious that the sprayed lubricant can be scattered everywhere when the motor shaft rotates. Make sure motor position is facing up so that the lubricant can penetrate down into the bearing. See photos below.


After the WD-40 seeps into bearing, then continue to apply lubrication oil to the motor shaft. I use a 20W-50 engine oil, which is applied by a syringe pump. See the photo below.


Rotate the shaft by hand, or by applying electric current to motor. Do it repeatedly until the sound of the motor become smoother, not noisy.

WD-40 lubricant is more dilute than oil so it seeps easily into bearing gap. If the oil is difficult to seep in, then spray again WD-40. That's why WD-40 lubricant is sprayed first in order to make the way for oil to seep.

The above procedure can also be applied to the air conditioner fan motor (pancake motor), as the following video.



At the beginning of the video, there is a rough noise from the motor, it sounds krkrkrkr when the motor rotates. The noise will sound louder if the fan and frame are fitted to the motor. Because the fan is made of plastic plate, and the frame is made of a metal plate. Both plates will be vibrating (resonance) so that motor noise will be much louder.

No need to open the motor housing. Because usually it will be difficult to put it back properly after the housing has been opened.

Sunday, October 23, 2016

Radiator & Air Conditioner Fan Motor Berisik





Radiator fan motor dan air conditioner condenser fan motor yang berisik dapat diperbaiki dengan melumasi as atau poros fan motor tersebut. Pelumasan dapat dilakukan dari luar tanpa perlu membuka rumah motor. Tapi kipasnya perlu dilepas agar tidak menutupi porosnya.

Ongkos perbaikan ini cukup murah jika dibanding dengan harga untuk membeli fan motor baru yang dapat mencapai ratusan ribu rupiah, bahkan ada yang mencapai jutaan rupiah.

Setelah diperbaiki maka poros motor akan berputar lebih lancar. Jika motor dihubungkan ke aki dan diukur dengan digital amperemeter maka terlihat jelas arus yang dikonsumsi jadi lebih kecil. Karena motor akan menghasilkan listrik jika porosnya diputar dengan tangan, jika diukur dengan digital voltmeter maka tegangan yang dihasilkan lebih tinggi setelah diperbaiki.

Baca juga fan motor menghasilkan listrik pada turbin angin.

Prosedurnya cukup mudah dan dapat dilakukan sendiri di garasi rumah. Pada beberapa kendaraan harus membuka selang radiator untuk dapat mengangkat rangka fan motor keluar. Ada juga ada yang harus membuka grill depan, terutama untuk dapat melepas dan mengeluarkan air conditioner fan.

Jika selang radiator harus dilepas, maka sebaiknya radiator coolant harus diganti baru. Jangan menggunakan kembali radiator coolant yang lama walau tampak masih bersih. Karena sifat kimianya mungkin sudah berubah karena tercemar oleh kotoran. Jika coolant tercemar dan bersifat lebih asam (korosif), maka radiator akan mudah berkarat. Jika radiator coolant belum tersedia, dapat diganti dengan air bersih. Dan nantinya radiator coolant dapat ditambahkan ke dalam radiator.

Setelah rangka kipas dilepas dari kendaraan, maka akan terlihat sebuah mur yang memegang kipas pada poros motor, sebagaimana foto berikut.



Kendorkan dan lepas mur tersebut. Lepas juga kipas dari poros motor.

Pada beberapa jenis motor terdapat ring pada poros motor. Ring tersebut akan terlihat setelah kipas terlepas, sebagaimana ditunjuk oleh panah merah pada foto di bawah.


Ring tersebut dapat dengan mudah dilepas dengan tangan.

Semprotkan pelumas WD-40 pada pangkal poros motor. Putar-putar poros dengan tangan. Poros boleh juga diputar dengan memberi tegangan untuk menghidupkan motor. Hati-hati jangan sampai pelumas yang sudah disemprotkan bertebaran kemana-mana saat motor dihidupkan. Pastikan posisi motor menghadap ke atas agar pelumas dapat meresap dan turun ke dalam bantalan (bearing) motor. Lihat foto di bawah.


Setelah WD-40 meresap, maka lanjutkan dengan memberikan pelumas oli pada poros motor. Saya menggunakan oli engine 20w-50 yang diaplikasikan dengan suntikan. Lihat foto berikut.


Putar lagi motor dengan tangan, atau hidupkan dengan memberi tegangan listrik pada motor. Lakukan berulang-ulang sampai suara motor jadi halus, tidak berisik lagi.

Pelumas WD-40 lebih encer dari oli sehingga mudah meresap masuk di antara celah poros dengan bantalannya. Jika oli sulit meresap masuk, maka semprotkan lagi WD-40. Itulah sebabnya pelumas WD-40 disemprotkan lebih dulu agar membuka jalan bagi oli untuk meresap.

Prosedur di atas dapat juga diterapkan pada air conditioner fan motor yang berbentuk datar (pancake motor), sebagaimana pada video berikut;


Pada bagian awal video terdengar suara kasar dari motor, ada suara 'krkrkrkr' saat motor berputar. Suara tersebut akan terdengar lebih nyata jika kipas terpasang dan fan dipasang pada rangkanya. Karena kipas terbuat dari pelat plastik, dan rangka fan terbuat dari pelat logam. Kedua pelat tersebut akan ikut bergetar (resonansi) sehingga suara kasar dari motor akan terdengar jauh lebih keras.

Tidak perlu membuka rumah motor. Karena biasanya akan sulit memasang kembali dengan benar jika rumah motor sudah dibuka.



Sunday, September 25, 2016

Small LED Powered By 220 Volts AC Without Transformer



The following video shows that small LED with a maximum supply voltage of about 3 vdc, it is supplied with a high voltage of 220 vac with a very simple circuit without transformer. One 1N4007 diode is used as a rectifier. One 330 kiloohms resistor is used as current limiter.



The following schematic has circuit components which are connected in series.


CAUTION: all parts of the circuits contained in this article are connected to high voltage, either directly or indirectly. Do not touch circuit while being connected to the high voltage. Use equipment that are well insulated.

As the above schematic:
VD is the voltage on the rectifier diode 1N4007
VL is the voltage on LED, or LED forward voltage
VR is the voltage on resistor 330 kiloohms
VAC is a supply voltage of 220 vac


When current is flowing in 1N4007 diode, it will be a voltage of 0.6 volts (VD) between the anode and the cathode pins. Diode is additional safety because LED cannot stand high reverse voltage. Usually the maximum allowable reverse voltage is only 5 volts, if more than that will immediately damage the LED. If the LED used is of good quality, then this diode can be removed. Shown in the video, LED is blinking at a frequency of 50-60 hertz. This happens because the diode and LED only allows half wave of alternating electric current. If you want to reduce LED blinking, you need to install a capacitor to stabilize the current, and use a diode bridge as a full wave rectifier.

LED that is used in video has diameter of 5 mm. This LED has a maximum forward voltage of about 3 vdc. There is also an LED that has only 2.2 vdc maximum voltage. Maximum forward current is usually around 30 mA. Therefore, the internal resistance of the LED can be calculated by using Ohm's law, with a maximum forward voltage of 3 volts:


LED resistance = Voltage / Current = 3 volts : 30 mA = 3 volts : (30 / 1000) amperes = 100 ohms


In the above schematic, VAC is 220 volts grid voltage, so the voltage between resistor pins is:

Resistor voltage = supply voltage - diode voltage - LED voltage = VR


VR = VAC - VD - VL =  220 - 0.6 - 3 = 216.4 volts


It is known that the maximum LED current is 30 mA. Because it is assembled in series, then the current is also flow through the resistor with an equal amperage. Therefore the resistor value can be calculated by Ohm's law:

Resistance = resistor voltage / resistor current = 216.4 volts / 30 mA = 216.4 volts : (30 / 1000) amperes = 7,213.33 ohms.


The above resistor value is the smallest value for maximum LED brightness, if the resistance is reduced then LED could be broken because over voltage.

In the video, the resistor has much higher value for safety, and to avoid LED light blinds the camera. With 330 kiloohms resistor, white LED is still very bright. If LED brightness is too low, the value of  resistor can be reduced from 330 kiloohms carefully.

In choosing resistor size, it is necessary to consider the power capacity of the resistor. For a 330 kiloohm resistor, the power calculation is:


Resistor power = resistor voltage x current = resistor voltage x resistor voltage / resistance

Resistor power = VR x VR / 330.000 = 216.4 x 216.4 / 330.000 =  0.14 watts


Since the current is intermittent or half-wave current, the actual power of the resistor is half of the power above, ie 0.07 watts. So, resistors with 1/4 or 1/2 watts power are widely available in the market, those resistors can be used safely.

Note that LED tends to keep the voltage values ​​at the anode and cathode remains stable. So the internal resistance of the LED will change according to the current through it. The  bigger the current, the lower the internal resistance of the LED. The smaller the current, the higher the internal resistance of the LED.

As seen in the video, although the current through the LED is very small about 0.67 mA, but the voltage on the LED pins still reach 1.06 volts. The voltage is measured by DC voltmeter, not AC voltmeter, because the current through the LED is direct current. Then the internal resistance of LED with such a small current is:


Resistance = 1,06 volts / 0,67 mA = 1,06 volts / 0,00067 amperes = 1.582,09 ohms

The actual value of the resistance and the voltage of the LED in the test in the video are higher from the value above, because only half the wave of alternating voltage is used to turn on the LED.

Theoretically, if there are many LEDs connected in series, then resistor is no longer needed to limit current. Example calculation: it is known LED with a maximum voltage of 3 volts DC, for 220 volt supply voltage will need LED as much as 220/3 = 73.3 pieces, which are connected in series. Of course that amount is the minimum amount, for safety reason then it should be more LEDs that are connected in series. And the rectifier diode is still needed for safety, only one (1x) piece.


The following schematic describes the circuit with a diode connected in parallel with the LED.


In the above circuit, the LED will light up when the current flows from left to right. LED will be off when current flows from right to left through diode, not through LED. The disadvantage of this circuit is that there is a power consumption when current flows from right to left, although the LED is not on.

The VL voltage will only occur when the LED is on. And the VD voltage will only occur when the LED is off. Since the current is alternating current, it will be difficult to measure the LED voltage (VL) accurately. The voltage on the resistor (VR) is alternating voltage.



In the above circuit, the resistor is replaced by a capacitor. When alternating current is applied, the capacitor will work like a resistor. The capacitor resistance is called reactance, because the resistance to the capacitor is the reaction of the capacitor to the alternating current. In order to obtain the correct reactance value, then the size of the capacitor can be calculated by the formula:


Capacitor reactance = Xc = 1 / (2 . Pi . f . C )


If the reactance of the capacitor is tuned equal to the resistance as in the previous circuit, ie 330 kilo ohm, and the frequency (f) of alternating voltage is 50 hertz. Then the size of the capacitor is:


C = 1 / (2 . Pi . f . Xc) = 1 / (2 x 22/7 x 50 x 330.000) = 9.65 x 10 ^ (-9) = 9.65 nanofarads


Or it can be rounded up to 10 nanofarads. But the problem is that this capacitor must be withstand to high voltage, reaching at least 250 volts. And this capacitor must also be of the type of capacitor for alternating current (AC), which is usually more expensive than direct current (DC) capacitors.

Theoretically the capacitor in this circuit will not generate heat. Because the capacitor discharges the electrical energy it holds, not in the form of heat energy. So there is no need for power calculations. But in practice the dielectric material inside the capacitor can generate heat, as the effect of the voltage changes. This often happens at high frequencies. Then we need a capacitor with a good dielectric, and of course the price is more expensive.

If the LED light is not bright enough, then the capacitor value is raised carefully. The nature of the capacitor with the alternating current is the inverse of the resistor. On the resistor, the higher the value the greater the resistant. In the capacitor, the higher the value the smaller the resistance to the alternating current, as can be calculated on the above reactance formula.

Video of testing LED with capacitor to connect to 220 VAC.



Sometimes LED is very sensitive and can not withstand reverse voltage. For that reason we need to add a rectifier diode, as the following scheme.



Seen in the above circuit, a rectifier diode is added in series to LED. So the LED is completely shielded from reverse voltage.

Due to the above considerations, of all suggested circuits, the topmost circuit is the best and recorded in video.

This circuit also can be applied to 110 volts AC with certain modification. This circuit can be applied as an LED meter, LED tester, LED indicator, and others.

Watch also video about LEDs in series for 9 volts, 12 volts, and 220 volts.


More detail about LEDs in series connection.






Saturday, August 27, 2016

LED Kecil Disuplai 220 Volt AC Tanpa Trafo



Video berikut memperlihatkan bahwa LED kecil dengan tegangan maximal sekitar 3 vdc. LED dicatu dengan tegangan tinggi 220 vac dengan rangkaian yang sangat sederhana tanpa transformator. Sebuah dioda 1N4007 digunakan sebagai penyearah. Sebuah resistor 330 kiloohm digunakan sebagai pembatas arus.





Baca juga membuat flasher sederhana untuk lampu rem mobil dan sepeda motor yang dapat berkedip.

Sirkuit berikut menggambarkan rangkaian komponen yang terhubung serie.

PERHATIAN: seluruh bagian dari rangkaian-rangkaian yang ada di artikel ini terhubung dengan tegangan tinggi, baik secara langsung maupun tidak langsung. Jangan menyentuh rangkaian saat sedang terhubung dengan tegangan tinggi. Gunakan peralatan yang terisolasi dengan baik.

Dari skema sirkuit di atas:
VD adalah tegangan pada dioda penyearah 1N4007
VL adalah tegangan pada LED
VR adalah tegangan pada resistor 330 kiloohm
VAC adalah tegangan suplai 220 vac

Pada dioda, jika dioda 1N4007 dilalui arus atau diberi tegangan maju, maka akan timbul tegangan sebesar 0.6 volt (VD) di antara kaki anoda dan katodanya. Dioda dibutuhkan sebagai pengaman tambahan karena LED tidak tahan tegangan terbalik. Biasanya tegangan terbalik maximal yang diperbolehkan hanyalah 5 volt saja, jika lebih maka LED langsung putus. Jika LED yang digunakan berkualitas bagus, maka dioda ini bisa ditiadakan. Tampak pada video lampu LED berkedip seperti bergetar pada frekuensi 50-60 hertz. Hal ini terjadi karena dioda dan LED hanya mengalirkan arus searah dengan setengah gelombang dari gelombang arus listrik bolak balik. Jika ingin mengurangi kedipan LED, maka dapat ditambahkan kondensor untuk meratakan arus, dan menggunakan dioda jembatan (kuproks) sebagai penyearah gelombang penuh.

LED yang digunakan pada video berdiameter 5 mm, LED ini mempunyai tegangan maju maximal sekitar 3 vdc. Ada juga LED yang bertegangan maximal hanya 2,2 vdc saja. Arus maju maximal biasanya sekitar 30 mA. Maka resistansi internal dari LED dapat dihitung menggunakan hukum Ohm, dengan tegangan maju maximal dianggap 3 volt:

Resistansi LED= tegangan / arus = 3 volt : 30 mA = 3 volt : (30 / 1000) ampere = 100 ohm



Pada skema di atas, VAC adalah tegangan jaringan listrik rumah yaitu 220 volt, maka tegangan di antara kaki-kaki resistor adalah:

Tegangan resistor = tegangan suplai - tegangan dioda - tegangan LED = VR

VR = VAC - VD - VL =  220 - 0.6 - 3 = 216,4 volt



Diketahui bahwa arus maximal LED adalah 30 mA, karena dirangkai serie maka arus tersebut juga melalui resistor dengan nilai ampere yang sama, sehingga nilai resistor dapat dihitung dengan hukum Ohm:

Resistansi = tegangan resistor / arus resistor = 216.4 volt / 30 mA = 216.4 volt : (30 /1000) ampere = 7.213,33 ohm.



Nilai resistor tersebut adalah nilai terkecil agar LED dapat menyala maximal, jika dikecilkan lagi maka LED bisa putus karena tegangannya jadi terlalu tinggi.

Pada video sengaja digunakan resistor yang jauh lebih tinggi nilainya agar aman, dan tidak menyilaukan kamera. Dengan resistor 330 kiloohm LED warna putih tersebut sudah menyala sangat terang. Selanjutnya jika memang LED kurang terang, maka resistor dapat diperkecil dari nilai 330 kiloohm secara hati-hati.

Dalam memilih ukuran resistor, maka perlu dipertimbangkan kapasitas daya dari resistor tersebut. Untuk resistor 330 kiloohm maka daya resistor adalah:

Daya resistor = tegangan resistor x arus = tegangan resistor x tegangan resistor / resistansi

Daya resistor = VR x VR / 330.000 = 216.4 x 216.4 / 330.000 =  0.14 watt


Karena arusnya adalah arus searah yang terputus-putus atau setengah gelombang, maka daya aktual resistor adalah setengah dari daya di atas, yaitu 0.07 watt. Maka resistor dengan daya 1/4 atau 1/2 watt yang banyak tersedia dipasaran dapat digunakan dengan aman.

Perhatikan bahwa LED cenderung menjaga nilai tegangan di kaki anoda dan katoda tetap stabil. Sehingga resistansi internal dari LED akan berubah sesuai dengan arus yang melewatinya. Semakin besar arus maka semakin rendah resistansi internal LED. Semakin kecil arus maka semakin tinggi restansi internal LED.

Sebagaimana terlihat dalam video, walau arus yang melalui LED sudah sangat kecil sekitar 0,67 mA, tapi tegangan pada kaki LED masih mencapai 1,06 volt. Tegangan tersebut diukur dengan DC voltmeter, bukan AC voltmeter, karena arus yang melewati LED adalah arus searah. Maka resistansi internal LED dengan arus yang sangat kecil tersebut adalah:

Resistansi = 1,06 volt / 0,67 mA = 1,06 volt / 0,00067 ampere = 1.582,09 ohm

Nilai aktual dari resistansi dan tegangan LED pada test di video lebih besar dari nilai tersebut di atas, karena hanya setengah gelombang dari tegangan bolak-balik yang dipakai menyalakan LED.

Secara teoritis, jika ada banyak LED disambung serie maka tidak dibutuhkan lagi resistor sebagai pembatas arus. Contoh perhitungan: diketahui LED dengan tegangan maximal 3 volt DC, maka untuk tegangan suplai 220 volt akan dibutuhkan LED sebanyak 220 / 3 = 73,3 buah yang disambung serie. Tentu jumlah tersebut adalah jumlah minimal, untuk amannya maka harus lebih banyak LED yang disambung serie.  Dan dioda penyearah tetap dibutuhkan sebagai pengaman, cukup satu (1x) buah saja.


Sirkuit berikut menggambarkan rangkaian dengan dioda terhubung paralel dengan LED.

Pada rangkaian di atas, LED akan menyala saat arus mengalir dari kiri ke kanan. LED akan mati saat arus mengalir dari kanan ke kiri melalui dioda, bukan melalui LED. Kelemahan rangkaian ini adalah, terdapat konsumsi daya listrik saat arus mengalir dari kanan ke kiri, walau LED tidak menyala.

Tegangan VL hanya akan timbul saat LED menyala. Dan tegangan VD hanya akan timbul saat LED tidak menyala. Karena arus yang melalui rangkaian adalah arus bolak-balik, maka akan sulit untuk mengukur tegangan LED (VL) dengan akurat. Tegangan pada resistor (VR) adalah tegangan bolak-balik.

Pada rangkaian di atas, resistor diganti dengan kapasitor. Jika dilalui oleh arus bolak-balik, maka kapasitor akan bekerja seperti resistor. Resistansi kapasitor disebut reaktansi, karena resistansi pada kapasitor adalah reaksi dari kapasitor tersebut terhadap arus bolak-balik. Agar didapat nilai reaktansi yang tepat, maka ukuran kapasitor dapat dihitung dengan rumus:

Reaktansi kapasitor = Xc = 1 / (2 . Pi . f . C )

Jika reaktansi kapasitor disetel sama dengan resistansi sebagaimana pada rangkaian sebelumnya, yaitu 330 kiloohm, dan frekuensi tegangan bolak-balik ( f ) adalah 50 hertz . Maka ukuran kapasitor adalah:

C = 1 / (2 . Pi . f . Xc) = 1 / (2 x 22/7 x 50 x 330.000) = 9.65 x 10 ^ (-9) = 9.65 nanofarad

Atau bisa dibulatkan menjadi 10 nanofarad. Tapi masalahnya kapasitor ini harus tahan terhadap tegangan tinggi, minimal mencapai 250 volt. Dan kapasitor ini juga harus dari tipe kapasitor untuk arus bolak-balik (AC), yang mana biasanya harganya lebih mahal dari kapasitor arus searah (DC).

Secara teoritis kapasitor pada rangkaian ini tidak akan menimbulkan panas. Karena kapasitor mengeluarkan kembali energi listrik yang ditampungnya, tidak dalam bentuk energi panas. Sehingga tidak perlu ada perhitungan daya. Tapi pada prakteknya material dielektrik di dalam kapasitor dapat menimbulkan panas, sebagai effek dari perubahan-perubahan tegangan. Hal ini sering terjadi pada frekuensi tinggi. Maka diperlukan kapasitor dengan bahan dielektrik yang bagus, dan tentu saja harganya lebih mahal.

Jika nyala LED masih kurang terang, maka ukuran kapasitor diperbesar secara hati-hati. Sifat kapasitor pada arus bolak-balik adalah kebalikan resistor. Pada resistor, semakin tinggi nilainya maka semakin besar hambatannya. Pada kapasitor, semakin tinggi nilainya maka semakin kecil hambatannya terhadap arus bolak-balik, sebagaimana dapat dihitung pada rumus reaktansi di atas.

Video pengujian LED dengan kapasitor untuk terhubung ke 220 VAC.



Adakalanya LED sangat sensitif dan tidak tahan terhadap tegangan terbalik. Untuk itu perlu ditambahkan dioda penyearah, sebagaimana skema berikut.


Tampak pada rangkaian di atas, ditambahkan sebuah dioda penyearah yang disambung serie dengan LED. Sehingga LED benar-benar terlindung dari tegangan terbalik.

Karena pertimbangan-pertimbangan di atas, dari semua rangkaian-rangkaian tersebut maka rangkaian yang disarankan dan akhirnya divideokan adalah rangkaian yang paling atas.

Rangkaian ini dapat juga diterapkan untuk 110 volt AC dengan modifikasi tertentu. Rangkaian ini dapat diterapkan sebagai LED meter, LED tester, juga LED indikator, dan lain-lain.

Baca juga cara merangkai lampu LED seri untuk tegangan tinggi, berikut perhitungan resistor pembatas arus. Lihat juga video pengujian rangkaian serie LED untuk 9 volt, 12 volt, dan 220 volt.



Tuesday, August 9, 2016

My Amazon Kindle Books

My Amazon shop Kindle format epub books. Some of these homemade books are using unused plastic sheet, polystyrene, rubber ban, drinking straw, ice cream stick, etc. to make science toys. Hopefully those books will help to reduce redundant household materials, promote plastic recycle at home, could become precious plastic products, and reduce plastic pollution.

These interesting science toy projects are guaranteed can be done at home. They will make you excited and wake up easily at Sunday morning.

Origami project with plastic sheet to make baking powder submarine




Plastic drinking straws electric boat and submarine




Homemade polystyrene boat or ship and plastic torpedo toys powered by Marangoni effect (different surface tension) 






Do it yourself wooden laser pistol and laser pointer, using laser beam for dry shooting practice.




Marangoni effect (different surface tension) power moves polystyrene toy boat or ship.




Thursday, July 28, 2016

Shy Little Cat Likes To Hunt Mouse



This video shows a little cat which like to hunt and eat mouse, but a bit shy.




Kucing Kecil Pemalu Suka Berburu Tikus

Video ini menunjukkan kucing kecil yang suka berburu dan makan tikus, tapi agak pemalu.

Wednesday, June 29, 2016

Sundanese Bamboo Raft Fisherman At Saguling Lake



A fisherman bamboo raft at Saguling lake, Padalarang, West Java, Indonesia. It is contrast with modern housings at background. Gps coordinates -6.8660097,107.4767258 , with camera is facing to south.


Sebuah rakit bambu nelayan di danau Saguling, Padalarang, Jawa Barat, Indonesia. Hal ini kontras dengan rumah modern pada latar belakang. Koordinat GPS -6.8660097,107.4767258, dengan kamera menghadap ke selatan.

Friday, June 3, 2016

Battery Powered Submarine Educational Science Toy




The following video shows the submarine is hovering very close to water surface, sometime it reaches water surface, or floats.


To set submarine floating on the water surface is fairly easy, making it sink is the easiest. But it is not easy to make the submarine hovering in the water. With this science toy, we can set it to hover in the water.

Ebook special for Kindle is available in the Amazon Kindle Store in some countries, with title as below:
"How To Make Science Toys Ship & Submarine: Made Of Household Materials, Battery Powered"





Read also baking powder submarine which can move like a real submarine although it is made only by origami of paper sheet and polystyrene and powered by baking powder.


This science toy submarine is driven by an electric DC motor and powered by 1x (one) AAA size battery. Submarine body is made of drinking straw, polystyrene, rubber bands, and colored plastic sheet.




Although it is made of household material, with a certain design this submarine educational toy can be set to float, hover in water, or dive to the bottom of swimming pool. The setting is done with no replacement of any component. This submarine can achieve speed 56 centimeter per second or about 1.8 foot per second.

Both of the following videos are featuring the submarine hovers in the water, about 20-50 cm below the water surface.




The video below shows the submarine set to dive to the bottom of swimming pool.


More info about boat and submarine science toys which can move like the real ones can be read in boat label.





Saturday, May 21, 2016

Mainan Sains Kapal Selam Tenaga Baterai



Bukunya tersedia di google play dan google books:

Kapal selam mainan sains ini digerakkan oleh motor listrik (dinamo) dengan tenaga dari 1x (satu) buah baterai ukuran AAA. Bodi kapal selam terbuat dari sedotan minuman, polystyrene (gabus), karet gelang, dan lembaran plastik berwarna.

Walaupun terbuat dari material yang ada di rumah tangga, dengan desain tertentu kapal selam mainan edukatif ini dapat diatur agar mengapung, melayang dalam air, atau menyelam ke dasar kolam. Pengaturan dilakukan dengan tidak ada penggantian komponen apapun. Kapal selam ini dapat mencapai kecepatan 56 centimeter per detik.

Video berikut memperlihatkan kapal selam melayang sangat dekat dengan permukaan air, terkadang muncul ke permukaan air, atau mengapung.



Baca juga: kapal selam bertenaga baking powder yang dapat menyelam, naik ke permukaan, dan berlayar seperti kapal selam sebenarnya.

Membuat suatu kapal terapung di permukaan air cukup mudah, membuatnya suatu kapal tenggelam adalah paling mudah. Tapi tidaklah mudah untuk membuat kapal selam melayang dalam air. Dengan mainan sains ini, kita dapat menyetelnya agar melayang di dalam air.

Kedua video berikut menampilkan kapal selam sedang melayang di dalam air, sekitar 20-50 cm di bawah muka air.





Baca juga: membuat origami kapal sabun yang dapat berlayar seperti kapal sebenarnya.

Berbagai kapal dan kapal selam yang dapat berlayar dan menyelam seperti aslinya dapat dibaca di label: boat.

Video di bawah menampilkan kapal selam yang disetel untuk menyelam hingga mencapai dasar kolam renang.





Friday, April 22, 2016

Lake Of Coal Mine Project Tenggarong East Kalimantan


The scenery of a lake which was a quarry of Multi Harapan Utama (MHU) coal mine project, Tenggarong, Kutai Kertanegara, East Kalimantan.


Pemandangan danau ini sebelumnya adalah bekas lubang tambang Multi Harapan Utama (MHU) proyek tambang batu bara, Tenggarong, Kutai Kertanegara, Kalimantan Timur.

Thursday, March 24, 2016

Drinking Straw Submarine In Swimming Pool





Ebook is available for purchase in the Amazon Kindle Store in some countries, with title as below:
"How To Make Science Toys Ship & Submarine: Made Of Household Materials, Battery Powered"


Drinking straw in video has been fitted with electric motor, battery, propeller, wing, and float to make it hover in the water. This science toy looks like a submarine or a torpedo. Because it has a polystyrene 'tower', I think it is more like a submarine than a torpedo.

It is an application of Archimedes' principle. It is not floating on water surface, but it is not sinking. Archimedes' principle: a water submerged object will get upward force equal to the weight of water displaced by the object. By calculating the weight of submarine, and submarine volume equal to the weight of water displaced, to allow submarine to hover in the water.

This science toy submarine is driven by a small direct current (DC)  motor which is powered by a single triple A (AAA) battery.

More info about boat and submarine educative toys which can move like the real ones can be read in boat label.


YouTube video address: https://youtu.be/rV3qQjdmEDk

Bukunya tersedia di google play dan google books



Kapal Selam Sedotan Minuman Di Kolam Renang
Sedotan dalam video telah dilengkapi dengan motor listrik, baterai, baling-baling, sayap, dan pelampung untuk membuatnya bergerak melayang-layang di dalam air. Mainan sains ini terlihat seperti kapal selam atau torpedo. Karena memiliki 'menara' polystyrene, saya pikir mainan ini lebih mirip kapal selam daripada torpedo.

Ini adalah aplikasi dari prinsip Archimedes. Kapal selam ini tidak mengambang di permukaan air, tapi juga tidak tenggelam. Prinsip Archimedes: benda yang terendam dalam air akan mendapatkan gaya ke atas sama dengan berat air yang dipindahkan oleh benda tersebut. Dengan menghitung berat kapal selam, dan volume kapal selam sama dengan berat air yang dipindahkan, untuk memungkinkan kapal selam agar melayang di dalam air.

Kapal selam mainan sains ini digerakkan oleh motor arus searah (DC) yang kecil dengan daya dari baterai tunggal triple A (AAA).

Baca juga berbagai mainan edukatif kapal dan kapal selam yang dapat berlayar dan menyelam seperti aslinya di boat label.

Thursday, February 25, 2016

Big Fishes In Sewer, Mangga Dua, Jakarta



There are some big fishes in Jakarta sewer. Dark grey fishes are about half meter length. Location at front of number 32 building at Mangga Dua Raya road, Ancol.

This is an evidence that sewer water in Jakarta still can provide good nutrition for fish farming. Hopefully all sewers in Jakarta will be much cleaner in the future, so it will be a lot more fishes in those sewers.

GPS coordinates of video location -6.137798, 106.8209162



Ikan Besar-besar Dalam Selokan, Mangga Dua, Jakarta

Ada beberapa ikan besar di selokan Jakarta. Ikan abu-abu gelap panjangnya sekitar setengah meter. Lokasi di depan gedung nomor 32 di jalan Mangga Dua Raya, Ancol.

Ini merupakan bukti bahwa air selokan di Jakarta masih dapat memberikan nutrisi yang baik untuk budidaya ikan. Mudah-mudahan semua selokan di Jakarta akan jauh lebih bersih di masa mendatang, sehingga akan lebih banyak ikan di dalam selokan tersebut


.

Wednesday, January 27, 2016

Homemade Baking Powder Powered Submarine Toy



This homemade toy submarine is powered by baking powder, no need battery / electric power. It can dive and surface, and also can move forward. This submarine science toy is using domestic item such as: origami of plastic paper and polystyrene. It looks like a real submarine. Those domestic materials are often wasted and useless, and become pollution. But now we can use them to make a beautiful working submarine like the real one.

Ebook Kindle format is available in the Amazon Kindle Store in some countries, with title as below:
"HOMEMADE WORKING MODEL SUBMARINE: BAKING POWDER POWERED"

The book is available at Google Play, or go to below address:

More info about boat and submarine science toys which can move like the real ones can be read in boat label.


Mainan kapal selam bikinan sendiri ini digerakkan oleh baking powder (bubuk pengembang kue), tanpa baterai / listrik. Kapal selam ini bisa menyelam dan kembali muncul ke permukaan, dan juga dapat bergerak maju. Kapal selam mainan sains ini menggunakan bahan-bahan rumah tangga seperti: origami kertas plastik dan polystyrene (gabus). Terlihat seperti kapal selam sebenarnya. Bahan-bahan rumah tangga tersebut sering terbuang percuma, dan menjadi polusi. Tapi sekarang kita dapat menggunakannya untuk membuat kapal selam yang indah bergerak seperti kapal selam sebenarnya.

Bukunya sudah tersedia di Google Play, atau di alamat berikut:
https://play.google.com/store/books/details?id=_trNCwAAQBAJ

Info lebih detail tentang membuat berbagai mainan sains perahu dan kapal selam yang dapat berlayar, menyelam, naik ke permukaan seperti sebenarnya di boat label.